bfPlatforms Manufacturer Series
3D-Bioplotter® Manufacturer Series

Built for the day your research becomes a product.

The commercialization configuration of the 3D-Bioplotter: five printhead stations, HD-camera calibration with photo logs, micron-level accuracy and a temperature-controlled build plate as standard.

Pencil illustration of the 3D-Bioplotter Manufacturer Series with five printhead stations
5
printhead stations, from any of 8 printheads
9 µm / 1 µm
XY / Z calibration accuracy
HD camera
for calibration and photo logs of every print
2 °C – 500 °C
printhead temperature range across the family
It's about trust

What changes when you move from the bench to production

In R&D, a good print is the goal. In manufacturing, you need to repeat it, prove it and document it. The Manufacturer Series is configured for that second job.

Pencil illustration of the precision extrusion system

Repeatable precision

Swiss-made 3-axis extrusion with camera-based calibration to 9 µm in XY and 1 µm in Z, on a vibration-resistant frame.

Pencil illustration of traceability log files

Medical-grade traceability

Post-print log files plus HD photo logs give each build a record, with multi-user management for who ran what.

Pencil illustration of automated calibration and cleaning

Process control

Temperature-controlled build plate as standard, temperature curves with up to five set points, and automated substrate height detection, needle cleaning and recalibration.

Pencil illustration of the 3D-Bioplotter frame

Sterile workflows

Designed for use in a biosafety cabinet, with sterile filters on the air supply for cell-compatible work.

Develop on one.
Manufacture on the other.

Developer and Manufacturer Series share the same core hardware, software and build envelope, so the process you prove in the lab carries straight into production.

  1. 01 · Developer Series
    Develop
    Materials, geometry and parameters
  2. 02 · Same software
    Transfer
    Move proven print files across platforms
  3. 03 · Manufacturer Series
    Manufacture
    Calibrate, print, log, repeat
Five stations

Multi-material builds in a single run

Load up to five printheads at once, mixing hydrogels, polymers, pastes and cell-compatible biomaterials in one construct. Two more stations than the Developer Series.

1
Both series
2
Both series
3
Both series
4
Manufacturer only
5
Manufacturer only
Low-Temperature2–70 °C
High-Temperature30–250 °C
Ultra-High-Temperature30–500 °C
Print and Cure2–70 °C · 365/405 nm
Photo Curing25 °C · 365–455 nm
Inkjet30–70 °C
2-Component30–70 °C
Co-Axial2–70 °C
Configurations

Manufacturer vs Developer Series

Manufacturer Series
Commercialization
Developer Series
Research & development
Printhead stations53
CalibrationHD camera · 9 µm XY, 1 µm ZLight sensor · 30 µm XY and Z
Photo logsIncludedNot available
Build plateTemperature-controlled, standardUpgradable, temperature control optional
Build envelope200 × 220 × 140 mm200 × 220 × 140 mm
Footprint976 × 623 × 773 mm976 × 623 × 773 mm
Core hardware & softwareSharedShared

Doing early-stage research? See the Developer Series.

Specifications

Footprint
976 × 623 × 773 mm
Weight
90–130 kg
Power
100–240 VAC
Compressed air
6–10 bar
Tips
Luer Lock, 0.1–1.2 mm

Upgrades & support

Pencil illustration of PrintRoll
PrintRoll™
Rotating drum for cylindrical scaffolds. Ships with a 10 mm drum; 20 mm, 40 mm and custom drums available.
Class II biosafety cabinet, compressor & booster
Everything around the machine for a clean production cell, plus consumables.
Worldwide support
For installation, training and ongoing service.

Planning to manufacture?

Tell us about your needs. We'll configure a Manufacturer Series system around it.

For the benefit of patient care